#1: Find out your wireless card chipset information
0c:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300
Please note down the 0c:00.0.
#2: Find out wireless card driver information
0c:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 Subsystem: Intel Corporation Device 1121 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Kernel driver in use: iwlwifi
#3: Disabling wireless networking ( Wi-Fi )
You may want to disable Wi-Fi on all laptops as it poses a serious security risk to sensitive or classified systems and networks. You can easily disable Wi-Fi under Linux using the techniques described in this tutorial.
#4: Configure a wireless network interface
iwconfig command is similar to ifconfig command, but is dedicated to the Linux wireless interfaces. It is used to manipulate the basic wireless parameters such as ssid, mode, channel, bit rates, encryption key, power and much more. To display information about wlan0 wireless interface, enter:
iwconfig Interface-Name-Here iwconfig wlan0
wlan0 IEEE 802.11abgn <strong>ESSID:"nixcraft5g"</strong> Mode:Managed <strong>Frequency:5.18 GHz</strong> Access Point: 74:44:44:44:57:FC <strong>Bit Rate=6 Mb/s</strong> Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off <strong>Link Quality=41/70</strong> <strong>Signal level=-69 dBm</strong> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:28 Missed beacon:0
In the above output iwconfig command shows lots of information:
- The name of the MAC protocol used
- ESSID (Network Name)
- The NWID
- The frequency (or channel)
- The sensitivity
- The mode of operation
- Access Point address
- The bit-rate
- The RTS threshold
- The fragmentation threshold
- The encryption key
- The power management settings
How do I find out link quality?
You can get overall quality of the link. This may be based on the level of contention or interference, the bit or frame error rate, how good the received signal is, some timing synchronisation, or other hardware metric.
# iwconfig wlan0 | grep -i --color quality
<strong>Link Quality=41/70</strong> Signal level=-69 dBm
41/70 is is an aggregate value, and depends totally on the driver and hardware.
How do I find out signal level?
To find out received signal strength (RSSI – how strong the received signal is). This may be arbitrary units or dBm, iwconfig uses driver meta information to interpret the raw value given by /proc/net/wireless and display the proper unit or maximum value (using 8 bit arithmetic). In Ad-Hoc mode, this may be undefined and you should use the iwspy command.
# iwconfig wlan0 | grep -i --color signal
Link Quality=41/70 <strong>Signal level=-69 dBm</strong>
Some parameters are only displayed in short/abbreviated form (such as encryption). You need to use the iwlist command to get all the details.
#5: See link quality continuously on screen
You can use /proc/net/wireless file. The iwconfig will also display its content as described above.
Better use the watch (gnuwatch, bsdwatch) command to run cat command repeatedly, displaying wireless signal on screen:
watch -n 1 cat /proc/net/wireless
Note: Again values will depend on the driver and the hardware specifics, so you need to refer to your driver documentation for proper interpretation of those values.
#6: Gnome NetworkManager
Gnome and many other Linux desktop operating system can use NetworkManager to keep an active network connection available at all times. he point of NetworkManager is to make networking configuration and setup as painless and automatic as possible. This package contains a systray applet for GNOME’s notification area but it also works for other desktop environments which provide a systray like KDE or XFCE. It displays the available networks and allows to easily switch between them. For encrypted networks it will prompt the user for the key/passphrase and it can optionally store them in the gnome-keyring.Please note that NetworkManager is configured through graphical interfaces, which are available for both GNOME and KDE.
#7: Say hello to wavemon
wavemon is a ncurses-based monitoring application for wireless network devices. It displays continuously updated information about signal levels as well as wireless-specific and general network information. Currently, wavemon can be used for monitoring devices supported by the wireless extensions, included in kernels version 2.4 and higher. Just type the following command to see the details:
#8: Other options
You can use the following tools too:
- Wicd which stands for Wireless Interface Connection Daemon, is an open source software utility to manage both wireless and wired networks for Linux.
- iwevent command displays Wireless Events received through the RTNetlink socket. Each line displays the specific Wireless Event which describes what has happened on the specified wireless interface. Sample outputs from iwevents:
Waiting for Wireless Events from interfaces... 07:11:57.124553 wlan0 Set Mode:Managed 07:11:57.124621 wlan0 Set ESSID:off/any 07:12:00.391527 wlan0 Scan request completed 07:12:10.428741 wlan0 Scan request completed 07:12:10.432618 wlan0 Set Mode:Managed 07:12:10.432642 wlan0 Set ESSID:off/any 07:12:10.432651 wlan0 Set Frequency:5.18 GHz (Channel 36) 07:12:10.432722 wlan0 Set ESSID:"nixcraft5g" 07:12:10.647943 wlan0 Association Response IEs:01088C129824B048606C2D1A7E081BFFFFFF00010000000000C20101000000000000000000003D16240D0000000000000000000000000000000000000000DD0 07:12:10.648019 wlan0 New Access Point/Cell address:74:44:44:44:57:FC 07:12:22.310182 wlan0 Scan request completed
- iwgetid command report ESSID, NWID or AP/Cell Address of wireless network. iwgetid is easier to integrate in various scripts. A sample output from iwgetid command:
- iwlist command Get more detailed wireless information from a wireless interface. A typical usage is as follows:
Usage: iwlist [interface] scanning [essid NNN] [last] [interface] frequency [interface] channel [interface] bitrate [interface] rate [interface] encryption [interface] keys [interface] power [interface] txpower [interface] retry [interface] ap [interface] accesspoints [interface] peers [interface] event [interface] auth [interface] wpakeys [interface] genie [interface] modulation
- man pages iwlist, iw, iwconfig, iwgetid, iwevent, iwlist
- Linux wireless wiki